[Fixed in 2.2.2] 2.2.1 Mikrotik Backups Are Being Replaced With One Line

Unimus support forum
Post Reply
TecWerks
Posts: 6
Joined: Fri Aug 07, 2020 11:47 pm

Tue Mar 01, 2022 4:22 pm

Hello,

I upgraded to 2.2.1 last night. My backups are set hourly, and I am seeing a few devices run a backup where the entire configuration is marked as deleted and replaced by "/export compact". Then on the next hour, the proper config returns.

So far this has happened a couple times on two Audiences and one hEX. They are running ROS 6.49.2
Last edited by TecWerks on Wed Apr 06, 2022 6:36 pm, edited 1 time in total.
User avatar
Tomas
Posts: 1206
Joined: Sat Jun 25, 2016 12:33 pm

Tue Mar 01, 2022 4:29 pm

Hi,

Sorry you are running into this - we would like to hotfix this ASAP. Could you please enable logging (Debug Log & Device output logging in Zones > Your_Zone > Debug Mode) and send us logs from a backup run that retrieves the backup incorrectly?

Please create a Support Ticket on the Portal with the logs attached and we will prioritize fixing this ASAP.
TecWerks
Posts: 6
Joined: Fri Aug 07, 2020 11:47 pm

Tue Mar 01, 2022 5:54 pm

Debug enabled, we'll see if any of them break at the top of the hour.
TecWerks
Posts: 6
Joined: Fri Aug 07, 2020 11:47 pm

Tue Mar 01, 2022 7:42 pm

Request 2301-794-430-45 created.
TecWerks
Posts: 6
Joined: Fri Aug 07, 2020 11:47 pm

Wed Apr 06, 2022 6:37 pm

This was resolved in 2.2.2 and I have updated the original post. Thanks much.
dexman
Posts: 1
Joined: Thu Apr 07, 2022 8:24 am

Thu Apr 07, 2022 8:27 am

Hi. I have 2.2.2 and still getting the same issue. Upgraded yesterday.

Example.
Backup 1

add action=accept chain=IPv4_IN prefix=0.0.0.0/0 prefix-length=32 set-type=blackhole

changed to

add action=accept chain=IPV4_IN prefix=0.0.0.0/0 prefix-length=32 set-type=\
blackhole

Next backup


add action=accept chain=IPV4_IN prefix=0.0.0.0/0 prefix-length=32 set-type=\
blackhole

changed to

add action=accept chain=IPv4_IN prefix=0.0.0.0/0 prefix-length=32 set-type=blackhole
Vik@Unimus
Posts: 198
Joined: Thu Aug 05, 2021 6:35 pm

Thu Apr 07, 2022 1:01 pm

This is not the same issue as the one described in the topic. This one was related to particular devices which had a problem with echoing a command (displaying the literal command) in the CLI, which took longer than one of our built-in timeouts causing the command itself being considered backup data.

We believe this was an isolated issue for Audience line as we later found out that the particular affected device from hEX line had some unrelated performance issues which would imitate the requirements for this issue to pop up.

As for the issue you describe, we are aware of this issue and we were unable to replicate the issue on our end with our devices (it is very inconsistent), but we are working on our own solution to handle this to handle line breaks regardless of line width (we have been setting terminal width to 200 characters when establishing sessions with MikroTiks).
Post Reply